솔지에로펜션(소나무숲길로)

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen can maneuver large panes of tempered glass from a height higher than the ground. They follow strict safety protocols and often work under harsh weather conditions.

Wearing protective clothing, take off the glazing points made of metal and all glazing putty using an utility knife. A heat gun will help soften and remove the old putty.

Replacement

If a window pane breaks, it could be tempting to try and repair the glass rather than replace it. However, replacing windows is typically more cost-effective, and can also aid in preventing other issues that could affect your home's energy efficiency. Examine the type of broken glass to determine if it's a temporary fix, or if a long-term solution is required.

To fix a damaged window, remove the frame or sash, and place it on the work surface. While wearing eye protection, carefully move the frame and remove any shards remaining in the window replacement. Utilize a utility knife to cut off the glazing compound and the glazing points that secure the window. Keep track of the components and their location so that they can be put back in place.

After you've removed the frame and sash you can begin preparing to replace the glass. Before you begin make sure that the opening in the frame is properly sized for your replacement window. Take measurements both ways across the opening, then subtract 1/8 inch from each measurement to allow the expansion and contraction of the frame and glass. Then, purchase double-strength glass cut to these exact dimensions. It is a good idea to purchase enough glazier's clips or points to install every 6 inches around the window pane.

If the manufacturer is responsible for this you should contact them and submit an claim. After the new glass has been installed, it needs to be bedded in with a thin layer of glazier's compound. After drying the compound and Window doctor dry, you can paint it to match the frame of the window.

If the crack is greater than an inch in length You can stop it from spreading by cutting an arc that is just a little beyond the crack. This method isn't completely foolproof, but it could slow the growth of the crack to a manageable amount until you are able to take more permanent measures.

Repair

Professional window contractors know how to handle a variety of glass, and they have the tools needed to complete the job correctly. They know how to dispose of waste properly and are therefore less likely than other people to leave behind scraps that could inflict harm on family pets or family members. They're also accustomed to working with various types of windows, and may be able to spot problems that a novice home owner might not be able to notice.

Wear safety goggles and gloves prior to starting repair work on cracked glass. Even a small crack can cause shards of glass to fly around and could pose a danger to anyone within or around the home. It's important to determine the cause of the crack, as this could prevent future issues.

Make a two-part mixture of epoxy. They typically are made up of a 50/50 mix of resin and hardener and must be mixed quickly. Once the mixture has been made and applied, simply apply it to the crack and let it dry. It should take only a couple of minutes, but it is important to work quickly because the mixture is extremely thick and dries quickly.

Once the epoxy has dried, you can get rid of excess epoxy using a putty blade. The next step is to clean around the cracked glass. If you don't do this properly, the residue can cause further damage to the glass. After cleaning the glass using a putty knife, you can use it to smooth the compound along the edge of the window, and then align it with the wood frame.

For a more durable solution think about using a plastic covering. You can cover the glass with masking tape or a strong-duty trashbag. This will prevent the crack from growing and will also block out wind, water, bugs, and debris.

If you're not able to get to the window doctor in a timely manner then you can apply silicone sealant to make an interim repair. Simply apply a small amount of the stuff around the outside of the broken pane. It won't completely fill the gap between frame and glass however it will keep the break in place while you repair it.

Repainting

Repainting old glass windows is a great idea. This is a cost-effective alternative to replacing windows and can give your home a new appearance. Make sure the surface is clean before painting. Clean the window with soap and water or use ruby alcohol to get rid of oil smudges and other traces which can hinder the paint from adhering. It is also recommended to wear rubber gloves when working on glass to avoid transferring your own oils onto the surface of the window. Apply several thin coats rather than one thick coat. This will allow the paint to last longer and keep your windows looking smooth and even.

Make sure you have the right tools in your arsenal when you are planning to repaint glass windows. You'll need a brush or sponge, painter's adhesive, a ruler, toothpicks, as well as a few other tools such as paper towels or a rag. You should also have the paint and brushes you'll need to complete the project. Make sure you follow the manufacturer's directions and be prepared with plenty of patience since it may take awhile for the paint to dry.

It is also important to ensure that the area you're working in is well ventilated, especially if you're using solvent-based paint. This will help to reduce the risk of breathing toxic chemicals, and the paint will dry faster. Use a mask that is protective when using spray paints.

For older glass windows, you'll need to prepare the surface prior to painting. Clean the glass window thoroughly using soap and warm water, then use rubbing alcohol to clean away any grease or oil that could hinder adhesion of the paint. Be sure that the windows are completely dry before you begin painting them.

If you have energy-efficient double-pane windows on your windows, it could be possible to file a claim for repair or replacement with the Window Doctor manufacturer or dealer who sold the windows. This is particularly true if you have experienced multiple problems with condensation or broken glass even though the windows are covered by warranty.

Sealing

There are a variety of options to fix the problem depending on regardless of whether you have an older double-pane window that has cracks in the seal or if you own a newer IGU (IGU) that has experienced fogging. The most costly option is to replace the frame and insulated unit but it may be necessary if condensation or fog is causing energy loss. Other options include replacing the existing IGU with a single-pane or repairing it by drilling a small hole in the bottom of the unit and then filling the solution with anti-fog.

You can also fill in the gap between the window frame and the threshold or Window Doctor sill with a felt strip, vinyl v-strips, or door sweep. Felt can be stapled, glued, or nailed into place but doesn't offer much protection against moisture. Vinyl v-strip weather stripping is durable and easy to install however it can be expensive and is generally used for areas that are subject to abrasions that are high. Door sweeps are cheap and can be put to the floor, but they create very little or no protection between the threshold or sill and dust, air and debris.

To fix a damaged window seal using a putty knife, you need to take off the caulk. Wearing gloves and eye protection carefully remove the glazing points -- small fasteners that fix the glass in the frame's recess using sharp, pointed ends. Once you have removed the glazing points, scrub the grooves and sand the wood to a smooth finish. Wipe off any sanding debris, then seal the bare wooden surface with a linseed-oil-based paint or clear sealer.

Traditional glazing putty can be applied using either a putty knife or a caulking gun, however using a knife allows for a more efficient, more precise application and provides a stronger seal. Choose a putty specifically for glass, as it will last longer and stick better.

Apply a small amount the putty to the inner edge of the frame where it meets the glass. Slide the window into the frame, so that the scribed line on the glass aligns with the frame's edge. Apply pressure on the glass to press the putty into a tight seal. Smooth the compound using gloves and then remove any drips or caulk that were not properly applied before it has dried.