솔지에로펜션(소나무숲길로)

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace window screen replacement Panes

A damaged or cracked window is an inconvenience. It could also be a chance to upgrade your glass to energy-efficient or insulated windows and benefit from greater comfort, a higher resale value and reduced utility costs.

You can do it yourself for less than what it would cost to employ an expert. It requires the right equipment and an hour or two of your time.

Glass

If your single-pane windows are old damaged, cracked or deteriorating replacing them with more modern insulated or tempered glass can improve energy efficiency and reduce noise while maintaining the historical integrity of older homes. The process of replacing a window pane is relatively simple and can be done by homeowners with basic hand tools. In addition to a new pane, the following items are required such as latex glazing putty; pliers, glazier's points and an electric heater to warm the old putty, if necessary. Wear safety goggles and gloves prior to beginning. Working with broken glass could cause serious injuries.

Begin by removing any remaining broken pieces of glass. It is best to use pliers for this however, a flathead may be used as well. Then, use a wooden chisel or putty knife take the remainder of the old putty from the frame and sash. Work slowly and carefully, taking care not to damage the old window sash. It is recommended to do this on a sturdy ladder instead of the ground and to place someone on the sash in order to help hold it in place.

Once you have removed all the old putty, it is time to prepare the window frame to accommodate the new pane. To allow for seasonal expansion or contraction, subtract 1/8 inch each from the measurements of the width and height. Take these measurements to the nearest hardware store or home center and have a piece of stock glass cut to size. You can cut the glass yourself if you possess the right tools.

After putting in the new pane, run a small bead of caulking around the edge to ensure it is weatherproof. Install a glazier’s point on both sides of the frame. This will ensure the pane. The points shouldn't be too tight that they cause friction between the frame and the sash However, they should not be loose.

Before applying the putty work it in a gentle manner until it is smooth and free of lumps. Then you can roll it into pencil-sized strips. Apply the first strip in the corner of the frame, moving from one corner to the next so that it is smooth and even.

Glazier's Points

The glazier's points are the small triangular pieces that allow glass to be secured into a Replacement Window Pane frame without scratching or damaging the fragile surface. It's simple to learn how to use this nefarious tool and you can save money on the expense of a professional installation.

Once the old putty and the glazier's point are gone and the frame is thoroughly cleaned using a utility knife to eliminate any remaining residue. Lightly sand the wood in the rabbet grooves to smooth rough areas. If you sand wood, protect it with painter's tape to protect it from damage caused by accidental sanding.

Take measurements of the empty frame and note down precise measurements. Bring these measurements to an hardware store or home center and have the new pane cut smaller than the frame's opening. This will ensure that the pane fits comfortably and allows for expansion and contraction.

Place the new pane in the frame and push it into place firmly using your hand. Then, use the tip of your chisel, or the back of the putty knife to tap in the glazier's points as shown in Figure 11. The glazier's points should be in line with the top edge of your pane and the shoulders raised should be just below the lip.

Apply a thin layer of glazing compound on the rabbet grooves as well as the edges of the new glass. This will protect and seal the edges. Allow this to dry and cure completely.

Install the new window sash after the double glazing replacement window compound has dried. First, coat the wood with a thick coat of Linseed oil. This will prevent the new putty from soaking in the moisture and deteriorating and cracking with time. Apply this coat with a brush or the edge of your putty knife, and then use the chisel, or the back end of the knife to gently hammer the new sash and glazier's point into the grooves of the rabbet. Repeat this procedure every 10 inches along the perimeter of the frame.

Putty

A baseball thrown or a rock thrown by error or a branch falling can cause a broken or cracked window. Fortunately, the majority of windows can be repaired by simply placing a new piece of glass in its the proper place. The glass is held in the position with a tiny metal clip, called a glazier’s point and putty. This compound is also referred to as glazing compound. Before you install a new pane, first remove the old one and clean up the area with a rag and an abrasive scraper that is a pull type or an abrasive wood chisel. Wear gloves and safety glasses while you do this work. If the window is secured to the frame, you'll need to make use of a heat gun to soften the adhesive before taking it off.

If you're planning to install your original sash, you must remove the mold that holds the old pane. Then, sand the sash to ensure it's smooth and ready for a new caulk. After the sash has been reinstalled then, you can apply a silicone caulk to the glass. This will ensure that it doesn't be leaking or fade over time.

Remove the glazing points from the rabbets, or the grooves in the sash where the glass is. If they are hard to chisel, use the hand tool, such as a heating gun over them to allow them to soften before. When using a heating tool, be careful to not damage the sash and its railings.

After the old glaze points and putty have been removed, prepare a bed for the new pane. Roll a rope with glazing compound between your fingers, and then make it about 1/2 inch thick. Press it into the rabbets where the glass will be put. The glass should rest against the putty on both sides. If needed you want to tap your glass lightly into the rabbet with your thumb.

If the new pane has cracked, you can apply the silicone caulk or glass glue that is based on solvents to fill in the crack prior to pressing it in the sash. If not, you'll have to putty over the crack to form a tight seal and keep water out. After the putty has dried, clean the oily film off the glass using an abrasive and allow it to dry completely prior to painting. Paint after the putty is completely dry. It won't make a strong seal and could discolor or leak over time.

Paint

If you've had a broken window pane, you might be worried about the cost of a new one. But the truth is that replacing one glass pane does not need to cost a fortune when you do it yourself. In fact even windows with double glazing replacement windows panes can be replaced at less than the cost of a professional.

If you are working with a large glass window first, ensure that it is securely fixed to the frame. This job can be made relatively simple and quick with the right tools and techniques.

When you are ready to start with the removal of the window pane. Remove the metal glazing points that are attached to it. These are basically small metal triangles that function as "nails" which hold the window in place within the frame of wood. They are placed under a glaze putty or bead that hardens to solid wedge that holds the wood frame securely in place and hides the sharp edges.

After you have removed the old pane removed, clean up the surrounding frame and wood. Scrape off any old paint and sand down the rabbet grooves in which the glazing points were placed. These should be sanded down to bare wood so that you can paint them the same color as the rest the frame. After sanding, apply a layer of flax oil to the wood's surface to prolong its life.

The next step is to determine the width of the window's opening. You'll need to take horizontal and vertical measurements of the entire opening and also the thickness of the old pane. To determine the exact dimensions of the new pane, subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. You can take these measurements to a hardware store or home improvement store and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.