솔지에로펜션(소나무숲길로)

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged window pane can be an inconvenience. It could also be a chance to upgrade your glass to energy-efficient or insulated windows to reap benefits like greater comfort, a higher the value of resales and lower utility bills.

It's a task you can do yourself for only a fraction of the cost of hiring a professional. It requires the right tools and an hour or two of your time.

Glass

Replace your single-paned windows with tempered or insulate glass to improve the efficiency of your energy, reduce noise, and maintain the original character of your home's older. The replacement of the window pane is easy and can be completed by homeowners with basic hand tools. You will also require a replacement handles for windows window pane, glazier's tips, pliers, and latex glaze putty. If you need to you may use a heatgun to warm the old putty. Before starting, wear gloves and safety glasses as working with broken glass can cause injuries.

Begin by removing any broken pieces of glass. It is best to use pliers for this, but a flathead can be used as well. Use a wood chisel, or putty knife to get rid of any remaining old putty around the frame and window sash. Be careful and slow and be careful not to damage the old window double glazing replacement sash. It is recommended to work on a sturdy ladder instead of the ground and to have someone stand below the sash in order to help hold it steady.

Prepare the window frame to accommodate the new pane once you have removed the old glue. Measure the width and height of the opening for the sash by subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). These measurements can be taken to an hardware or home centers store to get cut a piece of glass that is in stock to the correct size. You can cut the glass yourself if you possess the appropriate tools.

After installing the new pane, run a small bead of caulking around the edge to seal it against weather. Then install a glazier's point on the frame's opposite side to hold the pane in its place. The points should not be so tight that they cause friction between the sash and frame, but they also should not be too loose.

Before applying the putty make sure to knead it until it is smooth and free of lumps. Then, roll it into pencil-size strips. The first strip should be placed to the corner of the frame, working from one corner to the next so that it is smooth and even.

Glazier's Points

The glazier’s points are small triangular pieces of metal that allow glass to be secured into the window frame without causing damage to the delicate surface. It's easy to learn how to use this nefarious tool, and you'll be able to save money on the expense of an expert installation.

After getting rid of the old putty glazier points, and any other residue, clean the frame thoroughly using a utility knife. If necessary you can lightly sand the wood in the grooves of the rabbets to smooth out rough areas. If you do sand your wood, ensure you protect it by using painter's tape to prevent accidental damage.

Note down the exact dimensions of the frame. Take these dimensions to an hardware store or home center, and have the new pane cut slightly smaller than the frame's opening. This will ensure that the pane fits perfectly and allows for expansion and contraction.

Place the new pane into the frame and press it into place firmly using your hand. Then use the point of your chisel, or the back of the putty knife to make a tap on the glazier's points as shown in Figure 11. When you're done, they should be flush with the top edge of the pane. the shoulders of the points should be just below the lip of the rabbet groove.

Apply a thin layer of glazing compound to the rabbet grooves and the edges of the new glass. This will protect and seal the edges. Let it dry and cure fully.

When the glazing compound is dry, you're ready to install the new window sash. First, you need to coat the wood with a thick layer of linseed. This will stop the new putty from soaking up moisture and deteriorating and cracking over time. Use a brush to apply this coat, or the tip of the putty blade. Then use the chisel on the back of the putty tool or the back of the putty handle to gently hit the new sash, or glazier's point into rabbet grooves. Repeat this procedure every 10 inches around the frame's perimeter.

Putty

A baseball hit, a rock thrown in error, or a fallen tree can result in a cracked or cracked window pane. Fortunately, the majority of windows can be replaced by simply placing a new piece of glass in its the proper place. The glass is held in place using a small metal clip called the glazier's pointed and putty, which is often called glazing compound. Remove the old pane and clean the area using an abrasive, pull-type scraper or wood chisel. Wear protective glasses and gloves while you do this work. If the window is attached to the frame, you'll need to employ a heat gun in order to soften the adhesive before cutting it loose.

If you are planning to reinstall your original sash, you must remove the molding that supports the old pane. Sand the sash until it's flat and ready for new caulk. After the sash has been reinstalled then, you can apply a silicone caulk over the glass. This will ensure that it won't get soiled or discolor over time.

Take the glazing points out of the rabbets, or the grooves in the sash where the glass sits. If they're difficult to work out, try placing the hand tool, such as a heat gun over them to soften them before you do. If you're using a heating gun, be cautious not to damage the railings of the sash or the sash itself by holding the tool too tightly.

Once the old points of glazing and putty have been removed, prepare a bed for the new pane. Roll a rope made of glazing compound between your fingers, and then make it about 1/2 inch thick. Then, you can press it into the rabbets, where the glass will sit. The glass must rest against the putty on both sides. If necessary, lightly tap your glass into the rabbet with your thumb.

If the new pane is cracked you can fill it with a solvent-based glue or silicone caulk prior to pressing it into the sash. If the crack is not sealed, you will need to apply putty to keep water out. After the putty has dried remove the oily film off of the glass and let it dry completely before you paint. Paint before the putty has completely dried. It will not form a good seal and may be leaking or discoloring over time.

Paint

You might be worried about replacing a broken pane of glass. But the truth is that replacing one glass pane does not need to cost a fortune If you can do it yourself. Even double-paned windows can be replaced at a fraction of the cost it will cost an expert.

First, if you're working on a large-sized window, make sure that it is securely fastened to the frame. This task can be made relatively simple and fast using the proper tools and techniques.

When you are ready to start taking down the old window pane. Remove the metal glazing points attached to it. These are essentially small metal triangles that act as "nails" that hold the window in place in the wood frame. They are submerged beneath a bead or glazing glue that sets to form an unbreakable wedge that holds the wood frame in place and hides the points.

After you have removed the old pane taken away clean the surrounding frame and wood. Scrape off any old paint and sand the rabbet grooves in which the glazing points were. Sand them down to bare wood surfaces, so that you can paint the frames with the same color. After sanding the wood you can apply a layer flax oil. This will help to prolong the life of the frame.

Then, you need to measure the width of the window opening. You'll need to take horizontal and vertical measurements of the entire opening, as well as the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure you get the exact measurement for the new pane. This will also allow for expansion and contraction of the glass during seasonal change. You can take these measurements to a hardware store or home improvement shop and get the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.